4.16 main

Documentation/devicetree/bindings/clock/sunxi-ccu.txt

@@ -20,6 +20,7 @@ Required properties :
 		- "allwinner,sun50i-a64-ccu"
 		- "allwinner,sun50i-a64-r-ccu"
 		- "allwinner,sun50i-h5-ccu"
+		- "allwinner,sun50i-h6-ccu"
 		- "nextthing,gr8-ccu"
 
 - reg: Must contain the registers base address and length
@@ -31,6 +32,9 @@ Required properties :
 - #clock-cells : must contain 1
 - #reset-cells : must contain 1
 
+For the main CCU on H6, one more clock is needed:
+- "iosc": the SoC's internal frequency oscillator
+
 For the PRCM CCUs on A83T/H3/A64, two more clocks are needed:
 - "pll-periph": the SoC's peripheral PLL from the main CCU
 - "iosc": the SoC's internal frequency oscillator

Documentation/devicetree/bindings/display/msm/dsi.txt

@@ -102,7 +102,11 @@ Required properties:
 - clocks: Phandles to device clocks. See [1] for details on clock bindings.
 - clock-names: the following clocks are required:
   * "iface"
+  For 28nm HPM/LP, 28nm 8960 PHYs:
 - vddio-supply: phandle to vdd-io regulator device node
+  For 20nm PHY:
+- vddio-supply: phandle to vdd-io regulator device node
+- vcca-supply: phandle to vcca regulator device node
 
 Optional properties:
 - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY

Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt

@@ -20,7 +20,8 @@ Required subnode-properties:
 		gpio: cpuclkoutgrp0, udlclkoutgrp0, i2c1grp0, i2c2grp0,
 		      i2c3grp0, i2s0grp0, i2s1grp0, i2srefclkgrp0, spi0grp0,
 		      spi1grp0, pciedebuggrp0, uart0grp0, uart0grp1, uart1grp0,
-		      uart2grp0, uart2grp1, uart3grp0, uart4grp0, uart5grp0
+		      uart2grp0, uart2grp1, uart3grp0, uart4grp0, uart5grp0,
+		      uart5nocts
 		cpuclkout: cpuclkoutgrp0
 		udlclkout: udlclkoutgrp0
 		i2c1: i2c1grp0
@@ -37,7 +38,7 @@ Required subnode-properties:
 		uart2: uart2grp0, uart2grp1
 		uart3: uart3grp0
 		uart4: uart4grp0
-		uart5: uart5grp0
+		uart5: uart5grp0, uart5nocts
 		nand: nandgrp0
 		sdio0: sdio0grp0
 		sdio1: sdio1grp0

Documentation/networking/netdev-FAQ.txt

@@ -179,6 +179,15 @@ A: No.  See above answer.  In short, if you think it really belongs in
    dash marker line as described in Documentation/process/submitting-patches.rst to
    temporarily embed that information into the patch that you send.
 
+Q: Are all networking bug fixes backported to all stable releases?
+
+A: Due to capacity, Dave could only take care of the backports for the last
+   2 stable releases. For earlier stable releases, each stable branch maintainer
+   is supposed to take care of them. If you find any patch is missing from an
+   earlier stable branch, please notify stable@vger.kernel.org with either a
+   commit ID or a formal patch backported, and CC Dave and other relevant
+   networking developers.
+
 Q: Someone said that the comment style and coding convention is different
    for the networking content.  Is this true?
 

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 4
 PATCHLEVEL = 16
-SUBLEVEL = 11
+SUBLEVEL = 15
 EXTRAVERSION =
 NAME = Fearless Coyote
 

README.md

@@ -1,3 +1,2 @@
-
 Kernel 4.16 from mediatek for BPI-R2
 Please refer to [README.md](https://github.com/frank-w/BPI-R2-4.14/blob/4.14-main/README.md)

arch/arm/boot/dts/at91-nattis-2-natte-2.dts

@@ -146,7 +146,7 @@
 	};
 
 	eeprom@50 {
-		compatible = "nxp,24c02";
+		compatible = "nxp,se97b", "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 	};

arch/arm/boot/dts/at91-tse850-3.dts

@@ -246,7 +246,7 @@
 	};
 
 	eeprom@50 {
-		compatible = "nxp,24c02", "atmel,24c02";
+		compatible = "nxp,se97b", "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 	};

arch/arm/boot/dts/bcm283x.dtsi

@@ -252,7 +252,7 @@
 
 			jtag_gpio4: jtag_gpio4 {
 				brcm,pins = <4 5 6 12 13>;
-				brcm,function = <BCM2835_FSEL_ALT4>;
+				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
 			jtag_gpio22: jtag_gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
@@ -397,8 +397,8 @@
 
 		i2s: i2s@7e203000 {
 			compatible = "brcm,bcm2835-i2s";
-			reg = <0x7e203000 0x20>,
-			      <0x7e101098 0x02>;
+			reg = <0x7e203000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_PCM>;
 
 			dmas = <&dma 2>,
 			       <&dma 3>;

arch/arm/boot/dts/dra71-evm.dts

@@ -24,13 +24,13 @@
 
 		regulator-name = "vddshv8";
 		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3000000>;
+		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
 		vin-supply = <&evm_5v0>;
 
 		gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
 		states = <1800000 0x0
-			  3000000 0x1>;
+			  3300000 0x1>;
 	};
 
 	evm_1v8_sw: fixedregulator-evm_1v8 {

arch/arm/boot/dts/imx7d-cl-som-imx7.dts

@@ -213,37 +213,37 @@
 &iomuxc {
 	pinctrl_enet1: enet1grp {
 		fsl,pins = <
-			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
-			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
-			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
-			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
-			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
-			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
-			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
-			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
-			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
-			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
-			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
-			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
-			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
-			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
+			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x30
+			MX7D_PAD_SD2_WP__ENET1_MDC			0x30
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x11
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x11
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x11
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x11
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x11
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x11
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x11
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x11
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x11
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x11
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x11
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x11
 		>;
 	};
 
 	pinctrl_enet2: enet2grp {
 		fsl,pins = <
-			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x1
-			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x1
-			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x1
-			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x1
-			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x1
-			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x1
-			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x1
-			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x1
-			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x1
-			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x1
-			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x1
-			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x1
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x11
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x11
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x11
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x11
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x11
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x11
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x11
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x11
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x11
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x11
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x11
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x11
 		>;
 	};
 

arch/arm/boot/dts/keystone-k2e-clocks.dtsi

@@ -42,7 +42,7 @@ clocks {
 		domain-id = <0>;
 	};
 
-	clkhyperlink0: clkhyperlink02350030 {
+	clkhyperlink0: clkhyperlink0@2350030 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,psc-clock";
 		clocks = <&chipclk12>;